Manufacturer	Protocol	Requirements	Activ. Code
3S Codesys	PLC Handler	CoDeSys Runtime Ver. 2.3, Ver. 3.x
ABB	Modbus RTU	AC31, AC410 and others
ABB	Modbus TCP	AC31, AC410 and others
Allen Bradley	DF1	PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Allen Bradley	EtherNet/IP	PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Alstom	IEC-60870-5-104	Alstom RTU & Devices	*
Applicom	Applicom Communication server	PC1000 / PC2000 / PC4000
April	Modbus RTU	A2000 / 5000 / 7000 / PB80 / 200 / 400
Axel	Axel LogicLab	LogicLab SoftLogic Runtime
B+R	PVI interface	System 2000 and any other via PVI library
BACNet/IP	BACNet/IP - Annex J	Any standard device compliant Bacnet	*
Beckhoff	TwinCAT ADS	TwinCAT softPLC and I/O
Bosch Rexroth	MLPI	Bosch Rexroth device which supports the Motion Logic Programming Interface
CAN Open	CIFX	Profibus DP, Profinet, EtherCAT, PowerLink, CanOpen, Sercos and many other.
Carlo Gavazzi	Modbus RTU	Dupline
Control-Techniques	Modbus TCP/IP + CMP protocol	Control Techniques Modbus TCP supporting Modbus TCP/IP and CMP protocol
Control-Techniques	Modbus RTU + CMP protocol	Control Techniques devices supporting Modbus RTU and CMP protocols
Coster	C-Bus	Coster HVAC Controllers	*
CTI	NITP, CAMP, TCP/IP	CTI 2500 Series controllers with Ethernet interface
Texas Instruments	NITP, CAMP, TCP/IP	Ti 505 Plcs
Danfoss	Modbus TCP	Danfoss Control Unit
Echelon	LonWorks	Any LonWorks compatible device	*
EL.MO	CEI-ABI protocol specification 79/5 and 79/6	Elmo devices - Serial CEI-ABI	*
EL.MO	CEI-ABI protocol specification 79/5 and 79/6	Elmo devices - Ethernet CEI ABI	*
Elau	Modbus TCP	Elau CNC motion control
Elkron	Digit Serial protocol	Digit Controllers	*
Elkron	MP Serial protocol	MP110, MP120 Alarm Central	*
Elkron	ELK SirFire on TCP	Elkron FAP 500 control units	*
EtherCAT	CIFX	The Hilscher CIFX Card interface supports EtherCAT devices.
Endress + Hauser	Energy Manager RMS621		*
GE General Electric	SNP-X	Serial protocol for GE PLCs 90 Series, Micro Series
GE General Electric	SRTP2	Ethernet protocol GE PLCs 90 Series, Micro Series
Guardall	Guardall PS002 serial protocol	PX and QX Series	*
Hilscher	CIF 50	Profibus DP, Profinet, EtherCAT, PowerLink, CanOpen, Sercos and many other.
Hilscher	CIFX	Profibus DP, Profinet, EtherCAT, PowerLink, CanOpen, Sercos and many other.
Hilscher	NETx MPI	Simatic S7-300, S7-400, VIPA Plc
Hilscher	S7 MPI	Simatic S7-300, S7-400, VIPA Plc
Hitachi	Hitachi serial protocol	H-Series
Yaskawa MP	Yaskawa Ethernet Modbus IEC MP	Yaskawa Robot Controller IEC MP
IEC 60870-5-101	IEC 60870-5-101 unbalanced serial communication for remote controlled units RTU	Any RTU compliant, connected to a Controlling Station via RS232 or RS485	*
IEC 60870-5-104	IEC 60870-5-104 over TCP/IP, Client	Any RTU compliant, connected to a Controlling Station via TCP/IP networking	*
IEC 60870-5-104 Server	IEC 60870-5-104 over TCP/IP, Server	Any RTU compliant, connected to a Controlling Station via TCP/IP networking
IEC 61850	IEC 61850 MMS Client	Any IEC 61850 MMS server	*
Jetter	JetIPCOM7	Jetter Controller	*
Johnson Controls	System 91	TC-9100, DX-9100, XTM-105	*
Kernel	Kernel serial protocol	Kernel PLC
Konnex-EIB	Konnex, EIS from 1 to 15	Any KNX-EIB device	*
KW Software	ProConOs	ProConOS SoftPLC
Lenze	Lenze Serial	LecomAB
Mauell	IEC60870-5-104	Mauell RTU and PLC	*
Mitsubishi	Ethernet TCP	PLC MELSEC-Q Series
Mitsubishi	Format 1 with checksum serial protocol	PLC MELSEC-Q Series
Mitsubishi	Ethernet	PLC MELSEC-FX3U
Mitsubishi	Ethernet TCP	PLC Melsec-A series	*
Mitsubishi	PTP Serial protocol	PLC MELSEC-FX and MELSEC-FX2N PLCs and compatible
Modbus RTU Master	Modbus RTU/ASCII Slave	Any standard Modbus Master device
Modbus RTU Slave	Modbus RTU/ASCII Master	Any standard Modbus Slave device
Modbus TCP	Modbus TCP-IP client	Any standard Modbus Ethernet server
Moeller	Sucom Serial protocol	PLCs PS4-200, PS300 and PS400 series
Notifier	CEI Protocol Specification 79/5 and 79/6	Notifier Devices - Serial	*
Notifier	CEI Protocol Specification 79/5 and 79/6	Notifier Devices - Ethernet	*
Omron	EtherNet/IP	Omron NJ PLCs
Omron	Fins Ethernet	Omron SYSMAC PLCs
Omron	FINS Serial	Omron SYSMAC PLCs
Ova	Dardo Plus Protocol	Dardo Plus	*
Panasonic	MEWTOCOL protocol - serial and Ethernet communication	NAIS PLC FP Series
Phoenix Contact	Interbus	I/O and devices over Interbus
Phoenix contact	PLCI 2K	needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: "PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll
Phoenix contact	PLCI	needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: "PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll
Pixsys	LogicLab SoftLogic Runtime	Pixsys PLC devices
PowerLink	CIFX	The Hilscher CIFX Card interface supports PowerLink devices.
Profibus	CIFX	The Hilscher CIFX Card interface supports Profibus devices.
Profinet	CIFX	The Hilscher CIFX Card interface supports Profinet devices.
Rockwell Automation	DF1 Serial	PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Rockwell Automation	EtherNet/IP	PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
SAIA-Burgess	Saia S-Bus protocol (multi mode)	All PCD series PLCs
SAIA-Burgess	Saia Data Mode protocol	All PCD series PLCs
Sauter	BacNet/IP	Sauter PLCs supporting Bacnet	*
Schneider Electric	Modbus TCP	Modicon TSX and any standard Modbus Slave device
Schneider Electric	Modbus RTU/ASCII Master	Modicon TSX and any standard Modbus Slave device
Sercos	CIFX	The Hilscher CIFX Card interface supports Sercos devices.
Schneider Electric	Uni-Telway Slave	Telemecanique PLCs and Uni-Telway protocol compliant devices
Shared Memory	Open I/O data exchange	Customizable Data exchange with active processes through shared memory area
Siemens	SINAUT ST1	Siemens devices using SinautSt1 protocol
Siemens	AS511	Simatic-S5 Plcs
Siemens	DK3964R-RK512	Simatic-S5 Plcs
Siemens	S7-PPI	Simatic-S7-200
Siemens	S7-MPI	Simatic-S7-300-400
Siemens	S7-TCP	Simatic-S7-200-300-400-1200-1500
Siemens	TCP	Simatic-S7-200
Siemens	TIA PORTAL	Simatic-S7-1200-1500
Siemens	NET SAPI	All PLC S7 and CP Comm. Boards (CP5611, CP5613, CP5614)
SNMP	Ethernet SNMP	Any SNMP compliant device	*
Vipa	Can Bus	Contact the manufacturer for more details
Vipa	S7-TCP Protocol	VIPA System 200V, 300V, 300S
Vipa	S7-MPI Protocol	VIPA PLCs System 100, 200, 300, Speed7; Siemens PLCs S7 300 and 400 series and compatible
Vipa	Profibus DP Slave	Any Profibus DP Master controller
Wago	Modbus RTU	Any RTU controller or remote I/O
Wago	Modbus TCP	Any RTU controller or remote I/O
WITS	WITS Master Serial	devices that support Level 0 of the WITS protocol and transmit solicited data	*
MQTT Client	MQTT v3	support standard MQTT servers (brokers)
MT Connect	-	-

Siemens S7 TIA

The S7 TIA Symbolic Driver was designed specifically to access the SIMATIC S7-1200 and S7-1500 with symbolic addressing and accessing the optimized data blocks.
This driver needs the ACCON-AGLink software library (from DELTALOGIC Automatisierungstechnik GmbH) in order to communicate with server devices. The file of this library is named “AGLink40.DLL”.
Once you extract the “AGlink40.dll” file, you must copy it to the root of the Movicon installation file.

Interface Device: Siemens SIMATIC PLCs S7-1200/1500 series
Manufacturer: Siemens
Requirements: Require Ethernet board, Support PLC S7-1200 and S7-1500
Supported protocol: S7-TCP/IP TIA
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.53 DBL289

Movicon 11 Unicode – Unicode Rel. 11.4.1.53 DBL289 (Compatible with Version 11.6.1201 and later)

Course Calendar 2021

This calendar shows scheduled dates for free basic training courses or seminars based on the Progea software technologies.

Date	Offices	Time	Topic
22.02.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
08.03.2021	Webinar	9:00-10:30 14:00-15:30	Pro.Lean: Introduction session
12.04.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
19.04.2021	Webinar	9:00-10:30 14:00-15:30	Pro.Energy: Introduction session
10.05.2021	Webinar	9:00-10:30 14:00-15:30	Connext: Introduction session
07.06.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
14.06.2021	Webinar	9:00-10:30 14:00-15:30	Pro.Lean: Introduction session
12.07.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
13.09.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
11.10.2021	Webinar	9:00-10:30 14:00-15:30	Connext: Introduction session
25.10.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
15.11.2021	Webinar	9:00-10:30 14:00-15:30	Pro.Lean: Introduction session
13.12.2021	Webinar	9:00-12:00 14:00-17:00	Movicon.NExT: Introduction session
20.12.2021	Webinar	9:00-10:30 14:00-15:30	Pro.Energy: Introduction session

Course Calendar 2019

This calendar shows scheduled dates for free basic training courses or seminars based on the Progea software technologies.

Company Name	Address	Phone Number	E-mail Address	Web Site	Sectors
ETM SRL	Via F. Budi, 71 84018 Scafati (NA)	081 8509071	[email protected]	www.etmgroup.it	Automazione Industriale

Pixsys Soft-PLC

This driver is a third party driver, developed by Axel Software.

Progea does not provide technical support for this third party driver.

Contact technical support to download the drivers listed in the following links

Interface Device: Axel SoftPLC
Manufacturer: PageLab Softlogic
Requirements: –
Import Tags : Support Import Tags
Operating System : WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11

Movicon 11 CE

MT Connect

The MTConnect Driver was designed specifically to access data of shop-floor equipment from software applications used for monitoring and data analysis.
The agent, adapter, and device can be combined or separate and implemented in a device, a PC, or a combination.

TCP/IP is used to communicate with both the adapter and the agent by addressing their IP and port numbers. The default port number for an adapter is 7878 and the default port for an agent is 5000, though 80, the default HTTP port is frequently used. An agent responds to an application request with well-formed XML, where the adapter sends pipe-separated data to an agent.

Interface Device: –
Manufacturer: MT Connect
Requirements: The driver supports only Input tasks.
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.2 DBL283

MQTT Client

MQTT Client is a driver over TCP/ IP that implements a “publish-subscribe” lightweight messaging protocol client side. MQTT Client driver requires an MQTT message broker. The broker is responsible for distributing messages to interested clients based on the topic of a message.

The MQTT Client permits to associate a variable of the supervisor project to a topic. The “PUBLISH” messages exchanged by the driver with an MQTT broker contain the values of the tags associated to the topics.

Interface Device: Standard MQTT servers (brokers)
Manufacturer: MQTT
Requirements: MQTT v3 protocol supported
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL288

WITS Master Serial

WITS over serial works by exchanging packets over a full-duplex serial bus. In the synchronous mode, one system will request transmission of a packet from another system by sending a “dummy” packet. For example some EDR systems require a dummy packet, or a data packet, to be received before they’ll transmit back a packet. Sometimes a system will accept an empty dummy packet, other times it’s best to transmit some data in the dummy packet. For your dummy packet choose a null value or something non-volatile like the vendor string. (Rec: 19 Item: 84).

Interface Device: devices that support Level 0 of the WITS protocol and transmit solicited data
Manufacturer: WITS
Requirements: Supported protocol: WITS level 0, master, synchronous communication (solicited data)
Other requirements: RS-232, RS-422 or RS-485 line
Import Tags: Import Tags not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Vipa Profibus

The “VIPA PROFIBUS DP Slave” Driver is designed specifically for use on the VIPA HMI devices with integrated PROFIBUS interface. It is designed to communicate to a PROFIBUS DP Master.
The PROFIBUS DP Master should be configurated to communicate with a Slave with the opportune Input/Output modules. The Input/Output modules of the Slave will correspond to the data defined in the Supervisor.
The driver permits to exchange a maximum of 244 input bytes and 244 output bytes.

Interface Device: Any Profibus DP Master controller
Manufacturer: Vipa
Requirements: VIPA HMI devices with integrated PROFIBUS DP Slave interface
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Movicon 11 CE – Rel. 11.4.1.4 DBL282

Vipa MPI

The VIPA MPI Driver was designed specifically for use on the VIPA HMI devices with integrated MPI interface. It is designed to communicate to VIPA System 100, 200, 300 and Speed7 PLCs as well as with Siemens S7 300 and 400 PLCs, communicating via the MPI or Profibus interface. Any other device compatible with the S7-MPI protocol is supported.

Interface Device: VIPA PLCs System 100, 200, 300, Speed7; Siemens PLCs S7 300 and 400 series and compatible.
Manufacturer: Vipa
Requirements: VIPA HMI Device, MPI protocol Interface
Import Tags: Support Import Tags
Operating System: WIN 32/64,Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.3 DBL269

Movicon 11 CE – Rel. 11.4.1.3 DBL269

Vipa Embedded CAN

This driver is a third party driver, developed by Axel Software.

Progea does not provide technical support for this third party driver.

Contact technical support to download the drivers listed in the following links

Interface Device: CAN-Bus
Manufacturer: Vipa
Requirements: –
Import Tags: Import Tags not supported
Operating System: WIN 32/64,Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Movicon 11 CE – Rel. 11.4.1.4 DBL282

SNMP Manager

The SNMP driver permits to communicate with devices that support the SNMP (Simple Network Management Protocol) protocol. SNMP is an Internet-standard, introduced in 1988. This driver works as a SNMP “Manager”, and supports the following versions of the protocol: SNMPv1, SNMPv2c, SNMPv3. SNMPv3 augments the SNMP and SNMPv2 specifications with additional security and administration capabilities.
This driver implements the SNMP “Get” and “Set” requests to, respectively, read and write data from and to the connected devices. This driver does not manage “Trap” notifications. The devices must act as SNMP “Agents”. The database of a SNMP agent is called MIB (Management Information Base). Each value stored in a MIB can be addressed using a “readable” name or a numeric value, expressed in dot-notation, called OID (Object IDentifier). This driver uses OIDs in numeric format to address data.
The driver has been tested with Carel SpA devices, equipped with pCO Web modules.

Interface Device: Any SNMP compliant device
Manufacturer: Siemens
Requirements: SNMP Manager, for any devices supporting SNMP protocol acting as SNMP Agents
Import Tags: Import Tags not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Siemens NET Sapi

The Siemens Sapi-S7 Driver was designed specifically for use with Siemens S7 300 and 400 PLCs. This driver implements the so called S7 communications protocol, using the Siemens SAPI-S7 (S7 Simple Application Programming Interface) library.
The S7 protocol is a layer 7 communications protocol. It can be used on Profibus, MPI and Ethernet networks. The library SAPI-S7 (S732.DLL) is automatically installed when you install one of the products of the SIMATIC NET Software CD.

To access MPI and PROFIBUS networks, a Siemens CP board (CP5611, CP5613, CP5614) is required.
For Ethernet networks, dedicated Siemens Ethernet boards or also standard Ethernet boards can be used, but, in this last case, the installation of the libraries Softnet-S7 for Industrial Ethernet is required.

Before using the Supervisor driver, you must configure, using the specific Siemens Software, an “Access point”, corresponding to the PC board, a VFD (Virtual Field Device) on the board (by default the VFD is called Application or OPC Server), and the connection list on the VFD (each connection corresponds to a PLC of the network).

Interface Device: All PLC S7 and CP Comm. Boards (CP5611, CP5613, CP5614)
Manufacturer: Siemens
Requirements: Siemens – SAPI S7 Protocol for any Siemens card (Siemens CP board (CP5611, CP5613,
CP5614). Based on SAPI SoftNet Library
Import Tags: Support Import Tags
Operating System: WIN 32/64

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Siemens TCP

The Siemens S7 TCP Driver was designed specifically for the use with Siemens S7 300 and 400, but it can also be used with 200 series PLC. This driver implement the ISO over TCP protocol and the natural physical media is an Ethernet network, eventually connected with switches or hubs. Obviously, the PLC has to have an Ethernet port or an Ethernet module in its rack.

Interface Device: Simatic-S7-200
Manufacturer: Siemens
Requirements: Siemens S7- 200 Ethernet TCP-IP, Simatic Series 200
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.2 DBL265

Movicon 11 CE – Rel. 11.4.1.2 DBL265

Siemens S7 TCP

The S7 TCP Driver was designed specifically for the use with Siemens S7 300 and 400 and VIPA System 200V, 300V, 300S and 500S series. Also the PLC Siemens S7-1200 and S7-1500 are supported, with some limitations (see S7-1200 Ethernet Configuration and S7-1500 Ethernet Configuration). This driver implement the ISO over TCP protocol and the natural physical media is an Ethernet network, eventually connected with switches or hubs. Obviously, the PLC has to have an Ethernet port or an Ethernet module in its rack.
Once you extract the “AGlink40.dll” file, you must copy it to the root of the Movicon installation file.

Interface Device: Simatic-S7-200-300-400
Manufacturer: Siemens
Requirements: Siemens S7-300/400 TCP-IP Ethernet, Simatic Series 300-400 – For Windows CE
Support also PLC S7-1200 and S7-1500
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.23 DBL287

Movicon 11 CE – Rel. 11.4.1.23 DBL287

Siemens S7 MPI

The Siemens S7 MPI PC Adapter was designed specifically for use with Siemens S7 300 and 400 PLCs communicating via the MPI interface connected on the Serial RS232 port. The Siemens S7 MPI serial port adapter handles MPI connectivity on the PC.
This driver supports VIPA PLCs through Green Cable as well.
Any other device compatible with the S7-MPI protocol is supported.

The Siemens S7 MPI PC Adapter and the S7 MPI driver have been designed to allow more than one master device to exist on the network. This allows a programming package to operate while this driver is running or while additional PCs are accessing the network.

Interface Device: Simatic-S7-300 – 400
Manufacturer: Siemens
Requirements: Siemens S7 – MPI protocol for PC Adapter – SIMATIC PLCs S7-300/400 series
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Siemens S7 PPI

The Siemens S7 PPI Driver was designed specifically for use with Siemens S7 200 PLCs communicating via the PPI interface connected on the Serial RS232 port. The Siemens S7 PPI serial port adapter handles PPI connectivity on the PC.
Any other device compatible with the S7-PPI protocol is supported.

The S7 PPI driver supports Single Master Multidrop RS485 PPI networks via the Siemens PPI Serial cable. See the section “Cable” for more information.

Interface Device: Simatic-S7-200
Manufacturer: Siemens
Requirements: Siemens S7-Simatic S7-200 PPI protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Movicon 11 CE – Rel. 11.4.1.6 DBL286

Siemens DK3964R

The Siemens DK3964EX Driver was designed specifically for the use with Siemens S5 family CPU’s, by means of an appropriate communication board that implement the protocol. The S5 board are named CP524 and CP525, for the series 7 is possible to use the CP341. The protocol is a point-to-point protocol and do not allow to connect more than one device on the same communication channel.
The DK3964 protocol rules the exchange of ASCII frames between the PLC and the Supervisor; in order to carry on the communication one needs of an interpreter which analyze the frames. This interpreter is embedded in the communication boards previously named, but it is possible to make it run on the PLC cpu also. The interpreter is called RK512 and it is mandatory, for the communication to exists.

Interface Device: Simatic-S5 Plcs
Manufacturer: Siemens
Requirements: Siemens S5 – RK512 on DK3964R serial point-to-point protocol (CP524-525)
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

Movicon 11 CE – Rel. 11.4.0.2 DBL149

Siemens S5 CPU

The Siemens S5CPU Driver was designed specifically for the use with the Siemens S5 family of CPUs, old but yet available and diffused. This driver makes use of the programming port of the CPU, implementing a protocol that gives access to the DB area of the PLC and to the I/O areas; these latter only for reading and only for CPUs “Model 135”.

The protocol is of type point-to-point and does not allow to connect more than one device on the same channel of communication. The physical port available on the CPU of the PLC is a current loop one implemented on a female 15 pins connector.
This driver has been implemented to communicate with the PLC using the serial ports of the PC. Since the serial ports of the PC are, normally, RS-232 ports, it is necessary to apply a converter between the RS-232 interface and the current loop (TTY) interface. This converter is supplied by Siemens.

The driver has been tested with a PLC Siemens S5 135 CPU.[/text_output][text_output]

Interface Device: Simatic-S5 Plcs
Manufacturer: Siemens
Requirements: Siemens SIMATIC S5 – AS511 CPU interface (TTY current loop)
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.3 DBL150

Movicon 11 CE – Rel. 11.4.0.3 DBL150

Siemens ST1

The Siemens SINAUT ST1 driver has been designed to exchange data with Siemens devices equipped with modules that support the SINAUT ST1 protocol.
A connection must be established to remote devices in order to exchange data with them. The telecontrol LAN can be a dedicated or a switched LAN. This driver assumes that a serial connection (RS-232/RS-485) is available. If modems are used, the modem connection must be completely transparent for this driver.
The driver polls periodically the configured stations to get input data. For each station one input task must be defined. This input task is used by the driver to parse the received data and to pass them to the supervisor.
The driver permits also to send commands to the devices.
To achieve the maximum flexibility, the driver permits to define the device data structures (“Data Templates”), corresponding to the data that can be read/written from/to the devices. The drivers permits also to define the codes of the output commands (3 codes for each command).

Interface Device: Siemens devices using SinautSt1 protocol
Manufacturer: Siemens
Requirements: Siemens devices using Sinaut ST1 protocol RS-232 port
Import Tags: Import Tags no supported
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL282

Shared Memory

The “Memory I/O” driver permits to exchange data between the supervisor application and different programs (processes) running at the same time, using a local area of shared memory (a shared memory file). One process (the supervisor, for example) creates an area in RAM that other programs can access.

Interface Device: Customizable Data exchange with active
Manufacturer: Progea
Requirements: Open Data exchange with any third part applications through shared memory area
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Movicon 11 CE – Rel. 11.4.1.4 DBL282

Schneider Uni-Telway

This driver has been designed for communications with devices compliant with the protocol Uni-Telway (Schneider Telemecanique).
Uni-Telway is a Master-Slave, serial multi-drop protocol. This protocol is quite complex since it has been engineered to support large, multi-level networks.

Interface Device: Elemecanique PLCs and Uni-Telway protocol compliant devices
Manufacturer: Schneider Electric
Requirements: Schneider Electric – Telemecanique Unitelway (Slave)
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

Movicon 11 CE – Rel. 11.4.0.2 DBL149

Saia Data Mode

The SaiaDataMode driver has been developed to communicate with Saia-Burgess PCD series PLCs. It is a direct driver, not based on Saia libraries, making it possible to communicate in different ways:

S-BUS mode via S-BUS network (RS485). The connection needs a RS232/RS485 converter, in order to connect a serial port of the PC with a RS485 net that can hold a number of PLCs. (S-BUS).
S-BUS mode via Ethernet. The PC and the PLCs have only to be connected in the same Ethernet TCP/IP network, with address compatible with the current subnet. (SOCKET).

Interface Device: All PCD series PLCs with RS-485 or Ethernet port
Manufacturer: Saia
Requirements: Saia PLC – S-BUS, Ethernet, Serial (Data mode – No SAIA library required)
Import Tags: Import Tags not supported
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1.9 DBL286

Saia Multi Mode

The Saia® Multiport driver has been developed to communicate with Saia-Burgess PCD series PLCs. It is based on a Saia-Burgess library that make possible to communicate in five different ways:

PGU mode. Via a point to point RS232 connection between the Port 0 of the PLC and a serial port of the PC. (PGU)
S-BUS mode via S-BUS network (RS485). The connection needs a RS232/RS485 converter, in order to connect a serial port of the PC with a RS485 net that can hold a number of PLCs. (S-BUS)
S-BUS mode via Ethernet. The PC and the PLCs have only to be connected in the same Ethernet TCP/IP network, with address compatible with the current subnet. (SOCKET)
S-BUS mode via USB. (USB)
ProfiS-BUS mode. PC and the PLCs are connected in an Ethernet TCP/IP network. (PROFI-SBUS)

For every communication mode, the driver needs the Saia-Burgess communication library (SCommCom.dll) and driver (SCommDrv.exe) installed on the local PC.
This can be obtained by either installing SAIA® PG5 development software or the standalone, re-distributable SAIA® communication library. The driver requires version 1.3 or later of SAIA® communication library.

Please refer to Saia-Burgess documentation for more information on S-BUS settings.[/text_output][text_output]

Interface Device: All PCD series PLCs
Manufacturer: Saia
Requirements: SAIA Multiport (SAIA Library required)P800/S-BUS/Ethernet/ ProfiS-BUS/USB
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.12 DBL286

PLCI

The Phoenix Contact PLCI Driver was designed specifically to access, with symbolic addressing, the data of the following programmable logic controllers: ILC 1×1, AXC 1xxx, AXC 3xxx, and PC WORX RT BASIC/SRT.
This driver needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: “PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for PC desktop, “NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for panels with Windows Embedded Compact 7.

Interface Device: ILC 1×1 Series, AXC 1xxx Series, AXC 3xxx Series, PC WORX RT BASIC/SRT
Manufacturer: Phoenix Contact
Requirements: needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: “PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll
Import Tags: Yes
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.23 DBL288

Movicon 11 CE – Rel. 11.4.1.23 DBL288

PLCI BTP 2K

The Phoenix Contact PLCI Driver was designed specifically to access, with symbolic addressing, the data of
The Phoenix Contact PLCI BTP 2K Driver was designed specifically to access, with symbolic addressing, the data of the following programmable logic controllers: ILC 1×1, AXC 1xxx, AXC 3xxx, and PC WORX RT BASIC/SRT.
This driver needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: “PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for PC desktop,”PLCICE6.dll, “NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for panels with Windows CE 6.

Interface Device: ILC 1×1 Series, AXC 1xxx Series, AXC 3xxx Series, PC WORX RT BASIC/SRT
Manufacturer: Phoenix Contact
Requirements: needs the PLCI software libraries (from PHOENIX CONTACT Software GmbH ) in order to communicate with server devices: “PLCI.dll, NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for PC desktop,”PLCICE6.dll, “NativeMetaAPI.dll, MetaILP64_10.dll and MetaILP32_10.dll” for panels with Windows CE 6.
Import Tags: Yes
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.23 DBL288

Movicon 11 CE – Rel. 11.4.1.23 DBL288

Interbus

The Interbus Driver was designed for the use of the IBS PCI SC/I-T PCI board from Phoenix Contact, in order to communicate with remote devices over an Interbus type fieldbus. This driver also supports Ethernet communication with suitable devices.
This driver makes use of the DDI library from Phoenix Contact; this library manage directly the PCI board. The library and the low level Windows driver are supplied by the board manufacturer and must be installed before operating.

Interface Device: I/O and devices over Interbus
Manufacturer: Phoenix Contact
Requirements: Interbus-S Phoenix Contact – IBS PCI SC/I-T PCI board, Interbus cables, DDI library – For Windows CE
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Panasonic FP

Panasonic FP allows the data exchange with Panasonic FP series PLCs, using the MEWTOCOL protocol. The driver has been developed for both serial and Ethernet communication.
Before using the driver the PLC must be properly configured through the specific programming software. The Windows version is named “FPWIN GR” or “FPWIN PRO”. The PLC communication parameters may be set by the “Option\PLC Configuration…” menu command in the GR package, while in the PRO package the menu command is under “Online\Communication Parameters”.
The Panasonic FP Driver can communicate with either the PLC programming port (“Tool port”) or the PLC “COM port”. For the latter it is important to set the parameter “Port Selection” to the value “Computer Link”.

Note that with this setting the “Communication Format” parameters named “Terminator” and “Header” can be left to their default values (“CR” and “STX not exist”) because they are not used.

The Panasonic FP Driver can also communicate with FP PLCs using TCP/IP over Ethernet. In this case, the PLC must be wired to a Panasonic FP-WEB Server unit or to a FP2 ET-LAN unit. If this is the case, the PLC will be configured as above while FPWEB unit must be configured with the Panasonic provided “FP WEB Configurator” program.
Starting from version 10.1.0.9, the Panasonic FP Driver supports also the communication via the USB port of the PLC. In this case, the software “Panasonic Electric Works PLC Virtual UART” must be installed.

Please refer to Panasonic documentation for further information.

Interface Device: NAIS Matsushita PLCFP Series
Manufacturer: Panasonic
Requirements: Panasonic Nais FP – MEWTOCOL protocol – serial and Ethernet communication
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1.9 DBL286

OVA

The OVA DardoPlus Driver was designed specifically for the use with OVA DardoPlus emergency lightning controller. A number of DardoPlus devices could be connected in a RS485 net, the driver enters in the net by means of an RS232/RS485 converter.

Please, refer to the OVA documentation for the behaviour of the device and for the latest additions and features.

Interface Device: –
Manufacturer: OVA
Requirements: OVA Dardo Plus emergency lighting controllers – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

Omron Fins Serial

The Omron FINS Serial Driver was designed specifically for the use with Omron programmable controllers. This protocol connects a number of Omron controllers over a OMRON network.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron FINS Serial protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Omron Fins Ethernet

The Omron FINS Ethernet driver was designed specifically for the use with OMRON programmable controllers. This protocol connect a number of OMRON controllers over an Ethernet network.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron FINS Ethernet protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.10 DBL288

Movicon 11 CE – Rel. 11.4.1.10 DBL288

Omron Ethernet-IP

EtherNet/IP is an industrial networking standard that takes advantage of commercial off-the-shelf Ethernet communication chips and physical media. IP stands for ‘industrial protocol’ and it is what distinguishes this network. Unlike many options in the industrial Ethernet crowd, EtherNet/IP uses an open protocol at the application layer. Moreover, more than one vendor or organization backs EtherNet/IP. It is the only standard supported by three networking organizations: ControlNet International (CI), the Industrial Ethernet Association (IEA) and the Open DeviceNet Vendor Association (ODVA).

See the web site https://www.ethernet-ip.org for more information.

This driver has been expressly thought to communicate with Omron NJ PLC series over the Ethernet network. This driver uses symbolic tag addressing (tags names) with Ethernet/IP native commands.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron Ethernet-IP protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Movicon 11 – Unicode Rel. 11.4.1.4 DBL286 (Compatible with Version 11.6.1201 and later)

Movicon 11 CE – Unicode Rel. 11.4.1.4 DBL286 (Compatible with Version 11.6.1201 and later)

Notifier(CEI-ABI) Serial

The CEI ABI Notifier Serial driver permits to exchange data with NOTIFIER Am-2000/AM-6000 control units through a RS-232 or RS-485 line.
The communication protocol is based on the CEI specifications 79/5 and 79/6 with some specific variations.
The driver permits to receive alarm events from the control unit and to send commands to it. The driver can also send alignment requests to update the state of points (detectors/modules) and zones. It should be noted that the control unit does not send the event of return to normality when an alarm of a point ceases. In this case an alignment request can be sent to check the state of the point.
The driver has been tested with an AM-2000 control unit.

Interface Device: –
Manufacturer: CEI-ABI
Requirements: NOTIFIER Serial interfaces (2000-6000) CEI protocol based on specifications 79/5 and 79/6 – NEEDS ACTIVATION CODE
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL282

Notifier Ethernet

The CEI ABI Notifier Ethernet driver permits to exchange data with NOTIFIER devices connected to a CPU E-NET. The CPU E-NET must be connected to the Ethernet network by an ETH-C module. The connection between a device (for example an AM2000 central unit) and the CPU E-NET can be of any type: it doesn’t matter that the device is connected to the Ethernet network.
The communication protocol is based on the CEI specifications 79/5 and 79/6 with some specific variations.
The driver permits to receive alarm events from the devices connected to the CPU E-NET, and to send commands to them. The driver can also send alignment requests to update the state of points (detectors/modules) and zones. It should be noted that the devices do not send the event of return to normality when an alarm of a point ceases. In this case an alignment request can be sent to check the state of the point.
When the supervision application is started, the driver performs an initial alignment, downloading all the events stored in the memory of the CPU E-NET. This alignment can last some minutes.
The driver has been tested with an AM-2000 control unit connected to a CPU E-Net.

Interface Device: –
Manufacturer: CEI-ABI
Requirements: NOTIFIER Ethernet E-Net, ETH-C (2000-6000) CEI protocol based on specifications 79/5 and 79/6 – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

Moeller Sucom

This driver was designed for exchanging data with Moeller PLC, series PS4-200, PS300 e PS400. The communication is realized by means of a serial connection. This protocol is Master-Slave, where the PC is Master and tha PLC is Slave. This means that the PLC do not start communications, but answer to the interrogation coming from the PC. These PLC ha the accessible memory split in two pages: page 0 and page 1. With this protocol we can access only the page 0, and the only accessible area is the Merker area.
With this protocol you can realize point to point communication. From the point of view of the physical implementation, this is realized through a RS485 connection, with the aid of an RS232/485 converter. It can be used a Moeller serial converter, or any third party converter providing that have the automatic managing of the 485 port commutation between reception and transmission.

Interface Device: PLCs PS4-200, PS300 and PS400 series
Manufacturer: Moeller
Requirements: Moeller SUCOM serial protocol – PLCs PS4-200, PS300 and PS400 series
Import Tags: Import Tags Not supported
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

Movicon 11 CE – Rel. 11.4.0.2 DBL149

Modbus RTU

The Modbus Serial Driver was designed for use with serial devices that support the Modbus RTU or Modbus ASCII protocol as “Master”.
Modbus Protocol is a messaging structure developed by Gould Modicon in 1979, used to establish master-slave/client-server communication between intelligent devices. It is a de facto standard, truly open and the most widely used network protocol in the industrial manufacturing environment. It is literally implemented by hundreds of vendors on thousands of different devices in order to transfer discrete/analog I/O and register data between control devices.

Modbus is an application layer messaging protocol, positioned at level 7 of the OSI model, that provides client/server communication between devices connected on different types of buses or networks.
The Modbus protocol has been accepted by the IEC as a Public Available Specification (IEC PAS 62030).
The Modbus Serial driver has been developed to support a wide range of Modbus RTU compatible devices available in the automation world.

The driver permits also to send broadcast messages (only output requests) on device ID 0.

Interface Device: Any standard Modbus Slave device
Manufacturer: Modbus
Requirements: Modbus RTU or Modbus ASCII protocol as Master
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Movicon 11 CE – Rel. 11.4.1.6 DBL286

Mitsubishi Melsec FX

The Mitsubishi MELSEC-FX Driver was designed for use with Mitsubishi MELSEC-FX, FX1N, FX2N, FX3U PLCs or any compatible device. The communication protocol used by the driver is the serial point-to-point protocol configurated on the controller’s standard RS-422 port.

Interface Device: PLC MELSEC-FX and MELSEC-FX2N PLCs and
Manufacturer: Mitsubishi
Requirements: Mitsubishi – MELSEC-FX and MELSEC-FX2N Serial protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Movicon 11 CE – Rel. 11.4.1.6 DBL286

Mitsubishi Melsec TCP

The Melsec A TCP Driver was designed specifically for the use with Mitsubishi PLCs of the A series, connected to the PC through and Ethernet communication module.

This driver was tested with the PLC A2SHCPU and the Ethernet module A1SJ71E71N-T.
In order to configure the PLC for its IP address and port, please, refer to the Mitsubishi documentation and Support Service.

- Interface Device: PLC MELSEC-A series
- Manufacturer: Mitsubishi
- Requirements: Mitsubishi – MELSEC-A series Ethernet A1SJ71E71N-T
- Import Tags: Support Import Tags
- Operating System: WIN 32/64
- Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL282

Mitsubishi Melsec FX TCP

The Melsec FX TCP Driver was designed specifically for communication with Mitsubishi FX3U PLCs, connected to the PC through the Ethernet module FX3u-ENET. A number of PLCs can be connected over the Ethernet network. The FX3u-ENET module needs to be configured with a dedicated Mitsubishi software tool.

Interface Device: PLC MELSEC-FX3U
Manufacturer: Mitsubishi
Requirements: Mitsubishi – MELSEC-FX3U Ethernet TCP
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Mitsubishi Melsec Q Serial

The “Mitsubishi MELSEC-Q Serial Format 1” Driver was designed for use with Mitsubishi MELSEC-Q PLC equipped with a QJ71C24 communication module.
This module can have one RS-232 port and a RS-422/RS-485 port, or two RS-232 ports. The communication protocol used by the driver is the “Format 1 with checksum”.

Interface Device: PLC MELSEC-Q Series
Manufacturer: Mitsubishi
Requirements: Mitsubishi Melsec Q Serial (Format 1 with checksum, module QJ71C24)
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Mitsubishi Melsec Q TCP

The “Mitsubishi MELSEC-Q TCP” Driver was designed for use with Mitsubishi MELSEC-Q PLCs equipped with a QJ71E71 communication module, over Ethernet networks.
All the versions of the driver support the TCP/IP protocol as low level communication protocol. Starting from the version 10.1.0.2 of the driver, also the UDP/IP protocol is supported.

Interface Device:PLC MELSEC-Q Series
Manufacturer: Mitsubishi
Requirements: Mitsubishi Melsec Q Series, Ethernet TCP-IP protocol (QJ71E71 mod.)
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.7 DBL286

Movicon 11 CE – Rel. 11.4.1.7 DBL286

Lenze Lecom AB

The Lenze LecomAB Supervisor Driver was designed specifically for the use with Lenze frequency converter equipped with Lecom A/B communication module. Depending on the model of this communication module,one can connect and dialog with the frequency converter by means of an RS232 connection or with an RS485 serial bus, or with an optical fibre connection. In order to connect several frequency converter in the same net, one has to choose between RS485 and optical fiber connection. If one choose the RS485 connection an RS232/RS485 smart converter is required.

Please, refer to the Lenze documentation for the behaviour of the devices and for the latest additions and features.

Interface Device: Lecom AB
Manufacturer: Lenze
Requirements: –
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 dbl267

Movicon 11 CE – Rel. 11.4.0.1 DBL149

ProConOS

The SoCom driver was designed specifically to get in communication with ProConOS SoftPLC, connected through TCP/IP network protocols.
An instance of the ProConOS SoftPLC can be installed on a desktop computer or on a Windows CE panel; the driver is able to access both.

In order to establish the connection with the PLC, a valid program must run. Please, refer to the PLC and development environment documentation for more information and operating procedures.

Interface Device: Proconos SoftPLC
Manufacturer: ProConOS
Requirements: SoCom protocol for ProConOS SoftPLC (KW Software, Phoenix Contact)
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL287

Movicon 11 CE – Rel. 11.4.1.5 DBL287

Konnex -EIB

The EIBus – Konnex Driver was designed specifically to get in communication with Building Automation Devices, connected through EIB bus, or with the new Konnex System, which is the compatible successor of EIB.
EIB devices, like lights, dimmer, lamps, curtains, switches, …, have to be configured for their net address with the aid of the ETS software. In order to operate correctly with EIB devices, a good knowledge of the Konnex architecture and of the ETS software is required. For more information about this bus and the related tools, please refer to www.knx.org

Our driver can operate in different ways:

Serial communication between the PC and a Bus Coupling Unit (BCU) device, that represent the door of the EIB bus to the external world.
USB communication between the PC and a BCU device.
Ethernet communication, where the link between IP network and EIB devices are one or more EIBNet/IP routers.

Each communication channel requires a dedicated interface. See Requirements-Supported interfaces for details.

Communication with the bus is performed by the Falcon Software, which is the KNX/EIB protocol stack for Windows. Be sure to have properly installed the Falcon software, before starting any communication between the supervisor and your Konnex system. Please see Software requirements for any further info.

Interface Device: Any Konnex/EIB devices
Manufacturer: Konnex
Requirements: KONNEX- EIB – Falcon Library (Serial, Ethernet, USB) NEEDS ACTIVATION CODE
Import Tags: Support Import Tags
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.10 DBL286

Kernel

The Kernel Driver has been designed for use with Kernel devices. The driver permits to read and write the values of devices’ internal variables. The driver acts as Master. It is possible to create a network (RS422 or RS485) with more slaves. Each slave must have a different address.

Interface Device: –
Manufacturer: Kernel
Requirements: Kernel Sistem serial protocol
Import Tags: Import Tags Not supported
Operating System: WIN 32/64

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Johnson Controls System 91

The Johnson Controls 9100 Driver was designed for the use with Johnson Controls DX9100 and TC-9100 series controllers, by the “System 91” protocol. The driver implements the “single item” read/write messages of the protocol.

Interface Device: TC-9100, DX-9100, XTM-105
Manufacturer: Johnson Control
Requirements: Standard serial plug and cable; RS232/RS485 converter for connection to the N2 BUS
port.
Import Tags: Import Tags Not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL282

Jetter

The Jetter JetIP driver permits to communicate with Jetter devices equipped with an Ethernet port. This driver implements the version 7 of the Jetter communication protocol (Pcom7). The Ethernet version of the protocol uses UDP as the transport level protocol. A specific header is added in the data range of the UDP telegram. Moreover, the control characters of the serial version of the protocol are not used. So this driver cannot be used with RS-232/Ethernet converters, to communicate with Jetter PLCs that are not equipped with an Ethernet port. This driver implements only a part of the commands of the protocol JetIP. It permits to exchange data of the following data areas: Registers, Flags, Inputs, Outputs. Moreover, it implements the commands to check the model of the connected PLCs, and to start and stop the devices.
The driver can be used to communicate with the following PLCs:

Jet Control 241 (JC-241)
Jet Control 243 (JC-243)
Jet Control 246 (JC-246)
Jet Control 647 (JC-647)
JetMove

Interface Device: Jetter Controller
Manufacturer: Jetter
Requirements: Jetter – JetIP Eth Protocol PCom7 (JC-241, JC-243, JC-246, JC-647, JetMove) For Windows CE – NEED ACTIVATION CODE
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE
Require License Code for Movicon 11 version

Requires Runtime license option activation for 11.4 desktop versions

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 dbl149

Movicon 11 CE – Rel. 11.4.0.2 dbl149

IEC 61850

IEC 61850 is a standard for the design of electrical substation automation, and is a part of the IEC Technical Committee 57 TC57) reference architecture for electric power systems.
Data objects and control functionality of a substation are modelled into different standard logical nodes, which can be grouped under different logical devices.
The reporting of data of the server can be configured using reporting schemes called Report Control Blocks (RCB). The Report Control Blocks can be of two types: “Buffered” and “Unbuffered”. The sending of the data from the server to the client can be triggered using some pre-defined trigger conditions.
The services defined in the IEC 61850 standard have been mapped to different communication protocols.
This driver acts as an IEC 61850 client and implements the services mapping into the “Manufacturing Message Specification” (MMS) protocol, as described in the part 8-1 of the standard IEC 61850.
The MMS protocol is an international standard (ISO 9506) based on TCP protocol.
The driver supports the access to solicited data (Read/Write requests) and unsolicited data (MMS Information Reports).

Interface Device: Any IEC 61850 MMS server.
Manufacturer: IEC
Requirements: Standard Ethernet Card
Import Tags: Support Import Tags
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected]m, specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.15 DBL287

IEC 60870-5-104 Server

The IEC Technical Committee 57 ( Working Group 03) has developed a protocol standard for telecontrol, teleprotection, and associated telecommunications for electric power systems. The result of this work is IEC 60870-5. Five documents specify the base IEC 60870-5. The documents are:

IEC 60870-5-1 Transmission Frame Formats
IEC 60870-5-2 Data Link Transmission Services
IEC 60870-5-3 General Structure of Application Data
IEC 60870-5-4 Definition and coding of Information Elements
IEC 60870-5-5 Basic Application Functions

The IEC Technical Committee 57 have also generated a companion standard IEC 60870-5-104 especially for remote controlled units RTU, connected to a Controlling Station either via TCP/IP networking. The IEC 60870-5-104 is based on the five documents IEC 60870-5-1 – 5 and IEC60870-5-101.
The present version of this driver for IEC60870-5-104 supports the following protocol features: see IEC60870-5-104-Interoperability.
This driver implement the server-side of the communication protocol.

Interface Device: Any client supporting IEC 870-5-104 via TCP/IP networking
Manufacturer: IEC
Requirements: Any client supporting IEC 870-5-104 via TCP/IP networking IEC 60870-5-104 Server (controlled Station)
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL288

IEC 60870-5-101

The IEC Technical Committee 57 ( Working Group 03) developed a protocol standard for tele-control, tele-protection and associated telecommunications for electric power systems. The result of this work is IEC 60870-5.
Five documents specify the base IEC 60870-5.

The documents are:

IEC 60870-5-1 Transmission Frame Formats
IEC 60870-5-2 Data Link Transmission Services
IEC 60870-5-3 General Structure of Application Data
IEC 60870-5-4 Definition and coding of Information Elements
IEC 60870-5-5 Basic Application Functions

The IEC Technical Committee 57 also generated a companion standard IEC 60870-5-101 especially for remote controlled units RTU, connected to a Controlling Station either via V24(RS232) or RS485 serial communication. The IEC 60870-5-101 is based on the five documents IEC 60870-5-1 to 5.

The present version of this driver for IEC60870-5-101 supports Unbalanced Serial Communication. For a complete reference of the supported protocol features: see IEC60870-5-101- Interoperability.

Interface Device: Any RTU compliant, connected to a Controlling Station via RS232 or RS485.
Manufacturer: IEC
Requirements: IEC 60870-5-101 unbalanced serial comm. for remote controlled units RTU – NEEDS ACTIVATION CODE
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1. DBL286

Yaskawa MP iec Modbus

The “Yaskawa MP iec Modbus” driver permits to communicate with Yaskawa devices supporting the MODBUS TCP protocol, and with any other devices supporting this protocol as server.

Interface Device: standard Modbus TCP/IP
Manufacturer: Yaskawa
Requirements: Standard Ethernet card. Yaskawa MP iec, MP2600iec, MP23x0iec, MP3x00iec (<FW3.0), MP3x00iec (FW3.0), Modbus TCP/IP
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN Ce

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.3 DBL282

Movicon 11 CE – Rel. 11.4.1.3 DBL282

Hitachi Serial

This driver was designed for use with the programming port of the PLC CPU, or with a optional module, that HITACHI calls “Intelligent Serial Port Module” Comm-H. The CPU programming port allows a point to point communication, while the module Comm-H supports multi-point communication. The Comm-H module has two serial ports, one is the physical 422, the other is a standard 232.

This driver implement two protocols:
the first, named Mode 0, is a multi-point protocol, which can be used only with the Comm-H module. Using this configuration it is possible to connect up to 32 PLCs in a 422 net. The Mode 0 is also called One-Way Activation with Office Number.
the second, named Mode 1, is exclusively a point to point protocol and can be used also with the CPU programming port. The Mode 1 is also called One-Way Activation without Office Number.

This driver takes profit of the new function codes A0h and 0xAh, for reading and writing. These commands are not compatible with old Comm-H modules and CPUs. For this reason the driver supports also the commands 40h and 42h (see the option “Use commands 40h, 42h” in Station Properties).

Interface Device: H-Series
Manufacturer: Hitachi
Requirements: Require Dedicated 15 pins cable or Hitachi Comm-H module. Hitachi PLC, series H, serial protocol
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Hilscher S7 MPI

The Hilscher MPI driver provides MPI communication to Siemens or VIPA devices via the Hilscher MPI interface (Hilscher boards supporting PROFIBUS DP master + dedicated software).

Before the driver can be used, the appropriate software libraries must be installed from the Hilscher system CD and an appropriate system configuration must be set up. For further details please refer to “Desktop PC configuration”.
In order to use this driver with Windows CE devices, please refer to “Windows CE configuration”.

Interface Device: Simatic S7-300, S7-400, VIPA PLC
Manufacturer: Hilscher
Requirements:Hilscher CIF MPI/PB Cards and SyCon Configurator. Simatic MPI protocol via Hilscher CIF Card, (S7-300, S7-400, VIPA)
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Hilscher NETx MPI

The Hilscher NetX MPI Driver was designed specifically for the use with Siemens S7 300 and 400 and VIPA System 200V, 300V, 300S and 500S series, via the Hilscher NETcoreX MPI interface. Before the driver can be used, the appropriate software libraries must be installed from the Hilscher system CD and an appropriate system configuration must be set up. For further details please refer to NETcoreX Board Installation.

Interface Device: Simatic S7-300, S7-400, VIPA PLC
Manufacturer: Hilscher
Requirements: Simatic MPI protocol via Hilscher NETcoreX MPI board (S7-300, S7-400, VIPA)
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – el. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Hilscher Profobus DP Master

The Hilscher DPM driver provides Profibus DP communication capabilities to your system, using one of the suitable Hilscher Profibus DP Master boards. After properly configuring the Hilscher board by means of SyCon software package (supplied by Hilscher), your supervisor project will be able to exchange data with any Profibus-DP Slave device, such as digital I/O boards, analog I/O boards, and so on.
This driver has been tested with Hilscher CIF50-PB board.

Before the driver can be used, the appropriate software libraries must be installed from the Hilscher system CD.

Interface Device: Profibus DP, any compatible slave device
Manufacturer: Hilscher
Requirements: Hilscher PROFIBUS DP Master – CIF Cards
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Guardall

The Guardall PX/QX Supervisor Driver was designed specifically for the use with Guardall Alarm units of the series PX and QX. Supervisor connects to the Alarm unit by means of a serial RS232 connection.

Please, refer to the Guardall documentation for the behaviour of the devices and for the latest additions and features.

Interface Device: PX and QX series
Manufacturer: Guardall
Requirements: GUARDALL Alarm units, Serial protocol – PX and QX series – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL149

GE fanuc SRTP2

The GE SRTP2 driver has been developed to exchange data, through Ethernet lan, with GE PLCs series 90. The driver acts as a client. The SRTP2 protocol (Service Request Transfer Protocol 2), often referred to simply as SRTP, is an optimized version of the obsolete protocol SRTP.

Interface Device: GE Fanuc PLCs 90 series, GE Micro series
Manufacturer: GE-Fanuc
Requirements: GE SRTP2 (Ethernet) PLCs 90 series, PACSystems
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1.9 DBL286

GE fanuc SNP-X Serial

This driver has been developed to exchange data through serial cable with the series 90 GE Fanuc PLC’s, connecting the serial cable to the Cpu programming port or to the serial interface of a communication board. This communication board, in GE-Fanuc terminology, is named Serial communication co-processor CMM x11 or more precisely CMM 311 for the 90-30 series and CMM 711 for the 90-70 series. The protocol used is named SNP-X which is an optimized version of the older SNP protocol.

Notice that the programming port of the 90-70 series does not support the SNP-X, therefore with 90-70 a CMM-711 must be used to communicate with the device.

Using this protocol, it’s possible to establish a multi-drop communication of type 1:N.

A particular characteristic of this protocol is that the different stations of the network are identified by a Station Name instead of a number. The maximum number of stations that can be networked is 32.
The physical connection to the CPU programming port requires a special cable supplied by GE Fanuc, whereas if you use the CMM you have two possibilities depending on whether RS232 or RS422 is used. To make the corresponding cable, please consult the corresponding paragraph.

Interface Device: PLC Series 90, Micro Series
Manufacturer: GE-Fanuc
Requirements: Require Ethernet Board . GE Protocol SNP-X serial, PLCs 90 series, GE Micro series
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 DBL137

Movicon 11 CE – Rel. 11.4.0.2 DBL137

RMS621

he Endress+Hauser Energy Manager RMS621 Driver was designed specifically for the use with E+H RMS621 energy manager controller. The device, in its various versions, has a RS232 serial port, 1 RS485 serial port and 1 optional RS485 serial port. The PC could be connected to one of these serial port. Using the RS485 connection it is possible to address more than one device, providing that they have different Unit Number.
The RS232 port may exclude the second optional RS485 port; when the cable is connected to the RS232 port, the second optional RS485 port is disabled.

For more and updated information about these features take as reference the E+H official documentation of the device that you are going to use.

Interface Device: –
Manufacturer: Endress+Hauser
Requirements: Endress+Hauser RMS621 serial device – NEEDS ACTIVATION CODE
Import Tags: Import Tags not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.1 dbL149

Elkron Ethernet TCP

The “ELKRON FAP 500” driver has been developed according to the specifications of the “ELK SirFire communication protocol”. The driver encapsulates the messages of the “ELK SirFire protocol” into TCP frames, to permit the communication on Ethernet networks. The driver acts as a client and permits to receive alarm events from a control unit of the “FAP 500 series” and to send commands to it. The driver can also send polling requests to update the state of devices (detectors/modules), zones, groups, or to get a record, or the index, of one of the control unit event stacks and chronological log buffers. It should be noted that the control unit does not send the event of return to normality when an alarm of a device ceases. In this case a “Reset Event Data” command can be used to reset the data of the input tasks. After this command, the driver reinitialize its event scanning procedure, so that only active alarms or events are notified.

Interface Device: –
Manufacturer: Elkron
Requirements: ELKRON FAP 500 control units, protocol ELKSirFire Ethernet TCP – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.3 DBL282

Elkron Serial

The ELKRON MP110 Driver was designed specifically for the use with ELKRON Alarm Central of the family MP110 and MP120. The connection with the central is made via RS232; in order to connect the serial port of the PC with the central it is necessary to have, on the central, the optional TTL/RS232 module.

For more and updated information about these features take as reference the ELKRON official documentation of the devices that you are going to use.

Interface Device: –
Manufacturer: Elkron
Requirements: ELKRON devices, MP110 and MP120 – NEEDS ACTIVATION CODE
License Code: Require License Code
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.1 DBL262

Elkron Digit Italia

The “Digit Italia” driver permits to exchange data with “Digit Italia” control units, through a RS-232 or RS-485 line.
The driver permits to receive alarm events from the control unit and to send commands to it. The driver can also send polling requests to update the state of devices (detectors/modules), zones, groups, or to get a record of one of the control unit event stacks. It should be noted that the control unit does not send the event of return to normality when an alarm of a device ceases. In this case a “Reset Event Data” command can be used to reset the data of the input tasks. After this command, the driver reinitialize its event scanning procedure, so that only active alarms or events are notified.
The driver has been tested with a Digit Italia control unit.

Interface Device: Digit Italia controllers
Manufacturer: Elkron
Requirements: ELKRON SIRA – DIGIT ITALIA serial Devices – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This Diver has a limited warranty and could be not completely supported by Progea Support Team.

Before use it, you should check if the manufacturer still support the hardware devices, or contact Progea for more information.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.1 DBL149

CEI-ABI Ethernet

The CEI ABI Elmo Ethernet driver permits to exchange data with ELMO control units equipped with an Ethernet interface. The communication protocol is based on the CEI specifications 79/5 and 79/6. The protection level implemented is the level 0 with identification procedure.
The driver permits to receive alarm events from the control unit and to send commands to it. The driver can also send alignment requests to update the state of sensors, zones, and other elements. It should be noted that in certain cases the control unit could not send all the requested states. For example, if a request of alignment for all the sensors is sent, the central unit replies with only the states of the sensors with a danger situation.
The driver has been tested with an ETR128 control unit.

Interface Device: –
Manufacturer: CEI-ABI Elmo
Requirements: EL.MO Ethernet – CEI protocol based on specifications 79/5 and 79/6 – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.1 DBL149

CEI-ABI Serial

The CEI ABI Elmo Serial driver of Supervisor permits to exchange data with ELMO control units through a RS-232, RS-422 or RS-485 line.
The communication protocol is based on the CEI specifications 79/5 and 79/6. The protection level implemented is the level 0 with identification procedure.
The driver permits to receive alarm events from the control unit and to send commands to it. The driver can also send alignment requests to update the state of sensors, zones, and other elements. It should be noted that in certain cases the control unit could not send all the requested states. For example, if a request of alignment for all the sensors is sent, the central unit replies with only the states of the sensors with a danger situation.
The driver has been tested with an ETR128 control unit.

Interface Device: –
Manufacturer: CEI-ABI Elmo
Requirements: NOTIFIER Serial interfaces (2000-6000) CEI protocol based on specifications 79/5 and 79/6 – NEEDS ACTIVATION CODE
Import Tags: Import Tags not Supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 DBL274

LonWorks

The LonWorks Driver was designed specifically to monitor and control devices connected in a LonWorks network, described by a properly configurated LNS Database. To complete the task refer to the ©Echelon documentation about LonWorks or to LonWorks devices authorized manufacturers, installers or suppliers.

Interface Device: –
Manufacturer: LonWorks
Requirements: LonWorks – LonTalk protocol based on LNS for any LonWorks device.
Import Tags: Import Tags Not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.3 DBL282

CTITCP

The CTI 2500 Series Ethernet driver has been developed to communicate with the CTI 2500 Series Programmable Controllers of Control Technology Inc. These controllers are a compatible replacement for Texas Instruments and Siemens 505® systems. The driver acts as a client.

The communication protocol supported by the driver is the Common ASCII Messaging Protocol (CAMP). CAMP encapsulates several sub-protocols. The sub-protocol used by the driver is the Packed Task Code (PTC) sub-protocol that allows to place up to 14 task code requests in a single CAMP message. Task codes messages contained in the PTC message must be in the Non-Intelligent Terminal Protocol (NITP) format.

Interface Device: CTI 2500 Series controllers with Ethernet interface
Manufacturer: CTI
Requirements: Standard Ethernet Cable
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 dbl286

Movicon 11 CE – Rel. 11.4.1.6 dbl286

C-Bus

This driver is a third party driver, developed by Axel Software.

Progea does not provide technical support for this third party driver.

Contact technical support to download the drivers listed in the following links

Interface Device: COSTER devices using C-BUS protocol
Manufacturer: Coster
Requirements: RS-232, RS-422 or RS-485 line
Import Tags: Import Tags not supported
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.4 dbL282

Modbus Control Tecniques Serial

The Control Techniques Modbus Serial Driver has been designed to exchange data with serial Control Techniques drives that support the Modbus RTU protocol as “Master”.
The driver permits also to send broadcast messages (only output requests) on device ID 0.
In addition to standard MODBUS Function Codes (commands), the driver permits to send also commands of the CMP communication protocol, encapsulated into a MODBUS frame with Function Code 64 (which is referred to as “CMP Message” in the driver).
The driver supports the following commands of the CMP protocol: 16 = Read Object, 17 = Write Object.

Interface Device: All devices communication with standard Modbus serial protocol and Control Techniques drives supporting Modbus serial protocol and CMP protocol.
Manufacturer: Modbus – Control Tecniques
Requirements: Modbus RTU or Modbus ASCII protocol as Master
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.7 DBL286

Movicon 11 CE – Rel. 11.4.1. DBL286

Modbus Control Tecniques TCP

The Control Techniques Modbus TCP Driver has been designed to exchange data with serial Control Techniques drives that support the Modbus TCP protocol .
In addition to standard MODBUS Function Codes (commands), the driver permits to send also commands of the CMP communication protocol, encapsulated into a MODBUS frame with Function Code 64 (which is referred to as “CMP Message” in the driver).
The driver supports the following commands of the CMP protocol: 16 = Read Object, 17 = Write Object.

The devices can be direct part of an Ethernet network. The use of interconnection devices like bridge, router or gateway for interconnection between the TCP/IP network and a serial line sub-network permits connections of Modbus serial line client and server end devices.

This driver does not implement the Modbus messaging on TCP/IP service.

Interface Device: standard Modbus TCP/IP + CMP protocol
Manufacturer: Control Tecniques – Modbus
Requirements: Standard Ethernet card
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Movicon 11 CE – Rel. 11.4.1.6 DBL286

Hilscher NetX Multiprotocol

The Hilscher NetX Profibus Dp Slave driver provides communication to Profibus Dp Master devices via the Hilscher NETcoreX Profibus Dp Slave interface.

Before the driver can be used, the appropriate software libraries must be installed from the Hilscher system CD and an appropriate system configuration must be set up. For further details please refer to NETcoreX Board Installation.

Interface Device: Profibus DP, any compatible master device
Manufacturer: Hilscher
Requirements: PROFIbus DP Slave via Hilscher NETcoreX board – For Windows CE
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Bosch Rexroth MLPI

The Bosch Rexroth MLPI driver permits to exchange data with Bosch Rexroth devices which support the MLPI (Motion Logic Programming Interface) programming interface. The MLPI is a programming interface used to write C/C++ applications to configure and run a Bosch Rexroth device which supports the MLPI interface technology. One example is an IndraMotion MLC/XLC. The driver acts as a client.
This driver needs the MLPI software library (from Bosch Rexroth) in order to communicate with server devices. The file of this library is named “dllmlpiwin32.dll”.
The driver permits to Read/Write the symbolic variables of the connected devices. Moreover, it allows to choose the user and password parameters for the connection.

Interface Device: BoschRexroth device which supports the MLPI interface technology
Manufacturer: Bosch Rexroth
Requirements: Ethernet board, dllmlpiwin32.dll in the Supervisor system
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 dbl287

Twincat

This driver needs the ADS software library (from Beckhoff) in order to communicate with the routing system that rules every intermodule exchange of data. PLCs and I/O systems are controlled by the TwinCAT System Control Module, make sure that this Configuration end monitoring system is correctly set up and enabled, before establishing communication.
For the use of TwinCAT System Control and PLC, please refer to Beckhoff TwinCAT documentation.

Interface Device: Beckhoff TwinCat SoftPLC Beckhoff I/O
Manufacturer: Beckhoff
Requirements: Require ADS Software Library
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.25 DBL288

Movicon 11 CE – Rel. 11.4.1.25 DBL288

BacNet/IP

The BACnet/IP driver provides communication with devices supporting BACnet protocol in its implementation over IP.
BACnet is a protocol defined by ASHRAE (American Society of Heating, Refrigeration and Air-conditioning Engineers). The ANSI/ASHRAE Standard 135-2004 document contains the protocol definition. Annex to the document contains specification of the BACnet transported over IP, which is the implementation chosen for this driver.

The BACnet protocol has a number of services that permit to read/write the properties of the configured Data Objects. In order to get values of the Present_Value and Status_Flags properties, it is possible to request the values with a ReadPropertyMultiple or subscribing a COV (Change Of Value) notification for the Data Object. Using the ReadPropertyMultiple means poll the object with a request and receive an answer containing the data; using COV notification means subscribe to the device for a notification when Present_Value or Status_Flags of a Data Object change. This second way results in a spontaneous message from the device, whenever a Present_Value or a Status_Flags changes its value, reducing the traffic at the minimum.

Interface Device: Any standard device BacNet/IP
Manufacturer: BacNet
Requirements: Binary / Analog / Multistate – I/O and value
Import Tags: Support Import Tags
Operating System: WIN 32/64
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.10 dbL287

B&R

The “B&R PVI” Driver was designed specifically for use with B&R devices that implement the communication protocol INA2000.The connection can be a point to point serial connection (RS-232 or RS-422) or a multi-point Ethernet connection. This driver requests the installation of B&R PVI libraries.

The PVI base system essentially consists of the following components: the PVI Manager, the PVI Monitor, the PVICOM interface (client interface) and the PVI line. The driver links to the PVICOM library. For information about the configuration of the PVI system, please, refer to B&R documentation.

Interface Device: System 2000 PLCs
Manufacturer: B&R
Requirements: Require B&R PVI libraries, standard Ethernet or serial cable.
Support B&R devices that implement the communication protocol INA2000.
Import Tags : Support Import Tags
Operating System : WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.5 dbl286

Movicon 11 CE – Rel. 11.4.1.5 dbl286

Axel LogicLab Softlogic

This driver is a third party driver, developed by Axel Software.

Progea does not provide technical support for this third party driver.

Contact technical support to download the drivers listed in the following links

Interface Device: Axel SoftPLC
Manufacturer: PageLab Softlogic
Requirements: –
Import Tags : Support Import Tags
Operating System : WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11

Applicom

The Applicom Supervisor Driver was designed for the use with APPLICOM communication board, by means of APPLICOM.DLL function library. Because of the peculiarity of the APPLICOM board and software this driver can communicate with a number of different protocols, i.e. all the protocol supported by APPLICOM communication boards. Supervisor reads data through the Applicom database and writes data directly to the device, by means of the function available in the so called WAIT MODE.

For the reading processes, the driver make use of the datatabase access function, so it reads data already in the APPLICOM database. For these data to be updated, one has to define proper Read Cyclic Function that have to be executed with a certain frequency.
Writings goes directly to the device, with the help of specific function. The necessary data to address the right device and the right device data are taken from the variable’s associate Cyclic Function. For Input/Output tasks, the Read Cyclic Function is sufficient for both the reading and writing processes; for Output task it is necessary to define a Write Cyclic Function, disabled at the startup, that the driver will use only to get the device data necessary to perform the writings.

Interface Device: PC1000, PC2000, PC4000
Manufacturer: Applicom
Requirements: Applicom Server Interface PC/PCI 1500, 2000 Series
Import Tags : Import Tags not Supported
Operating System : WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.0.2 dbl149

IEC 60870-5-104

The IEC Technical Committee 57 ( Working Group 03) have developed a protocol standard for telecontrol, teleprotection, and associated telecommunications for electric power systems. The result of this work is IEC 60870-5. Five documents specify the base IEC 60870-5.

The documents are:

IEC 60870-5-1 Transmission Frame Formats
IEC 60870-5-2 Data Link Transmission Services
IEC 60870-5-3 General Structure of Application Data
IEC 60870-5-4 Definition and coding of Information Elements
IEC 60870-5-5 Basic Application Functions

The IEC Technical Committee 57 have also generated a companion standard IEC 60870-5-104 especially for remote controlled units RTU, connected to a Controlling Station either via TCP/IP networking. The IEC 60870-5-104 is based on the five documents IEC 60870-5-1 – 5 and IEC60870-5-101.

The present version of this driver for IEC60870-5-104 supports the following protocol features: see IEC60870-5-104-Interoperability.

Interface Device: Any RTU compliant, connected to a Controlling Station via TCP/IP networking.
Manufacturer: IEC
Requirements: IEC 60870-5-104 for remote controlled units RTU via TCP/IP – NEEDS ACTIVATION CODE
Import Tags: Import Tags not supported
Operating System: WIN 32/64, WIN CE
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1.9 DBL286

EtherNet/IP

EtherNet/IP is an industrial networking standard that takes advantage of commercial off-the-shelf Ethernet communication chips and physical media. IP stands for ‘industrial protocol’ and it is what distinguishes this network. Unlike many options in the industrial Ethernet crowd, EtherNet/IP uses an open protocol at the application layer. Moreover, more than one vendor or organization backs EtherNet/IP. It is the only standard supported by three networking organizations: ControlNet International (CI), the Industrial Ethernet Association (IEA) and the Open DeviceNet Vendor Association (ODVA).

Interface Device: PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Manufacturer: Rockwell Automation (Allen Bradley)
Requirements: Rockwell Allen-Bradley – EtherNet/IP (PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix)
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.23 DBL286

Movicon 11 CE – Rel. 11.4.1.23 DBL286

DF1 Serial Protocol

The DF1 driver supports the Rockwell Allen-Bradley DF1 serial Protocol. The DF1 protocol is normally supported by any Allen-Bradley PLC’s family. Anyway the DF1 communication driver has been tested with:

PLC5
SLC500/xx
MicroLogix
ControlLogix (using the “Tag/File Mapping”)
CompactLogix (using the “Tag/File Mapping”)
FlexLogix5434 (using the “Tag/File Mapping”)
CPU Logix5000 series

Interface Device: PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Manufacturer: Rockwell Automation (Allen Bradley)
Requirement/Description: Rockwell Allen Bradley DF1 and Data Highway protocol (PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix)
Supported Protocols: DF1 Full-Duplex (point-to-point communication), DF1 Half-Duplex Master (multi-drop communication) also known as DF1 Polled-Mod
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.6 DBL286

Movicon 11 CE – Rel. 11.4.1.6 DBL286

Modbus TCP

Modbus TCP driver has been developed on the basis of Modbus protocol, according to Modbus specification. The driver acts as a client and allows communication with many devices classes supporting this protocol, such as PLCs, remote terminal units, analyzers, I/O modules, sensors, controllers, AC/DC drive control devices.

The devices can be direct part of an Ethernet network. The use of interconnection devices like bridge, router or gateway for interconnection between the TCP/IP network and a serial line sub-network permits connections of Modbus serial line client and server end devices.
This driver does not implement the Modbus messaging on TCP/IP service.

Modbus TCP/IP specification has been developed in 1999. The specification of this protocol and its implementation guide can be obtained on www.modbus.org.
Combining a versatile, scalable, and ubiquitous physical network (Ethernet) with a universal networking standard (TCP/IP) and a vendor-neutral data representation (Modbus ® ) gives a truly open, accessible network for exchange of process data.

Interface Device: Any standard Modbus Ethernet device
Manufacturer: Modbus
Requirements: Modbus TCP-IP Ethernet protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – – Rel. 11.4.1.18 DBL286

Movicon 11 CE – Rel. 11.4.1.18 DBL286

Modbus Slave

The MODBUS Slave Driver was designed for use with serial devices that support the MODBUS RTU or MODBUS ASCII protocol as “Master”.
MODBUS Protocol is a messaging structure developed by Gould Modicon in 1979, used to establish master-slave/client-server communication between intelligent devices. It is a de facto standard, truly open and the most widely used network protocol in the industrial manufacturing environment. It is literally implemented by hundreds of vendors on thousands of different devices in order to transfer discrete/analog I/O and register data between control devices.

MODBUS is an application layer messaging protocol, positioned at level 7 of the OSI model, that provides client/server communication between devices connected on different types of buses or networks.
The MODBUS protocol has been accepted by the IEC as a Public Available Specification (IEC PAS 62030).
The MODBUS Slave driver has been developed to support a wide range of MODBUS compatible devices available in the automation world.

The driver simulates one or more MODBUS slaves, defined as stations. The data of the slaves can be defined as tasks, associating the tags of the supervisor to the MODBUS addresses of a slave (station).
The driver supports the following Function Codes: 01H = Read Coils, 02H = Read Discrete Inputs, 03H = Read Holding Registers, 04H = Read Input Registers, 05H = Write Single Coil, 06H = Write Single Register, 07H = Read Exception Status, 0FH = Write Multiple Coils, 10H = Write Multiple Registers.
The driver manages also broadcast messages (messages sent to the dummy slave 0) for the following Function Codes: 05H, 06H, 0FH, 10H.

For more information, please see the section “Addressing”.

Interface Device: Any standard Modbus Master device
Manufacturer: Modbus
Requirements: Modbus RTU or Modbus ASCII protocol as Slave
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – Rel. 11.4.1.9 DBL286

Movicon 11 CE – Rel. 11.4.1.9 DBL286

3S CoDeSys

The CoDeSys Driver was designed specifically to get in communication with 3S Software softPLC, connected through TCP/IP network protocols.
An instance of the CoDeSys SoftPLC can be installed on a desktop computer or on a Windows CE panel; the driver is able to access both.
Our driver support two different PLC version: 2.3 and 3.x
The runtime and the Programming environment are different for the two versions, for the configuration of the 3S system, please refer to their documentation.

The version 3 PLC need a 3S dll, in order to complete the connection. The GwClient.dll must be present in the client system, in the Supervisor directory or in a directory included in the path environment variable.

In order to establish the connection with the PLC, a valid program must run and the program symbols must be exported. Please, refer to the PLC and development environment documentation for more information and operating procedures.

Interface Device: CoDeSys Runtime Ver. 2.3, Ver. 3.x
Manufacturer: 3S CoDeSys
Requirements: Require Ethernet board, GwClient.dll in the client and Supervisor system, 3S dll for connecting to version 3 PLC. 3S CoDeSys TCP/IP Protocol supported by the PLCHandler library
Import Tags : Support Import Tags from device
Operating System : WIN 32, WIN CE
Require License Code for Movicon 11 version

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon 11 – – Rel. 11.4.1.23 dbl287

Movicon 11 CE – – Rel. 11.4.1.23 dbl287

SNMP Manager

The SNMP driver permits to communicate with devices that support the SNMP (Simple Network Management Protocol) protocol. SNMP is an Internet-standard, introduced in 1988. This driver works as a SNMP “Manager”, and supports the following versions of the protocol: SNMPv1, SNMPv2c.
This driver implements the SNMP “Get” and “Set” requests to, respectively, read and write data from and to the connected devices. This driver does not manage “Trap” notifications. The devices must act as SNMP “Agents”. The database of a SNMP agent is called MIB (Management Information Base). Each value stored in a MIB can be addressed using a “readable” name or a numeric value, expressed in dot-notation, called OID (Object IDentifier). This driver uses OIDs in numeric format to address data.

Interface Device: Any SNMP compliant device
Manufacturer: Various
Requirements: SNMP Manager, for any devices supporting SNMP protocol acting as SNMP Agents
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Siemens S7 PPI

The Siemens S7 PPI Driver was designed specifically for use with Siemens S7 200 PLCs communicating via the PPI interface connected on the Serial RS232 port. The Siemens S7 PPI serial port adapter handles PPI connectivity on the PC.
Any other device compatible with the S7-PPI protocol is supported.

The S7 PPI driver supports Single Master Multidrop RS485 PPI networks via the Siemens PPI Serial cable. See the section “Cable” for more information.

Interface Device: Simatic-S7-200
Manufacturer: Siemens
Requirements: Siemens S7-Simatic S7-200 PPI protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Siemens S7 TIA

The S7 TIA Symbolic Driver was designed specifically to access the SIMATIC S7-1200 and S7-1500 with symbolic addressing and accessing the optimized data blocks.
This driver needs the ACCON-AGLink software library (from DELTALOGIC Automatisierungstechnik GmbH) in order to communicate with server devices. The file of this library is named “AGLink40.DLL”.

Interface Device: Siemens SIMATIC PLCs S7-1200/1500 series
Manufacturer: Siemens
Requirements: Require Ethernet board, Support PLC S7-1200 and S7-1500 , ACCON-AGLink software library
Supported protocol: S7-TCP/IP TIA
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Siemens S7 MPI

The Siemens S7 MPI PC Adapter was designed specifically for use with Siemens S7 300 and 400 PLCs communicating via the MPI interface connected on the Serial RS232 port. The Siemens S7 MPI serial port adapter handles MPI connectivity on the PC.
This driver supports VIPA PLCs through Green Cable as well.
Any other device compatible with the S7-MPI protocol is supported.

The Siemens S7 MPI PC Adapter and the S7 MPI driver have been designed to allow more than one master device to exist on the network. This allows a programming package to operate while this driver is running or while additional PCs are accessing the network.

Interface Device: Simatic-S7-300 – 400
Manufacturer: Siemens
Requirements: Siemens S7 – MPI protocol for PC Adapter – SIMATIC PLCs S7-300/400 series
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Siemens S7 TCP

The S7 TCP Driver was designed specifically for the use with Siemens S7 300, 400, 1200, 1500 and VIPA System 200V, 300V, 300S and 500S series. This driver implement the ISO over TCP protocol and the natural physical media is an Ethernet network, eventually connected with switches or hubs. Obviously, the PLC has to have an Ethernet port or an Ethernet module in its rack.

Interface Device: Simatic-S7- 300 – 400 – 1200 – 1500
Manufacturer: Siemens
Requirements: Siemens S7 – TCP protocol – SIMATIC PLCs S7-300/400/1200/1500 and compatibles PLC series
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Saia Data Mode

The SaiaDataMode driver has been developed to communicate with Saia-Burgess PCD series PLCs. It is a direct driver, not based on Saia libraries, making it possible to communicate in different ways:

S-BUS mode via S-BUS network (RS485). The connection needs a RS232/RS485 converter, in order to connect a serial port of the PC with a RS485 net that can hold a number of PLCs. (S-BUS).
S-BUS mode via Ethernet. The PC and the PLCs have only to be connected in the same Ethernet TCP/IP network, with address compatible with the current subnet. (SOCKET).

Interface Device: All PCD series PLCs with RS-485 or Ethernet port
Manufacturer: Saia
Requirements: Saia PLC – S-BUS, Ethernet, Serial (Data mode)
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

EtherNet/IP

EtherNet/IP is an industrial networking standard that takes advantage of commercial off-the-shelf Ethernet communication chips and physical media. IP stands for ‘industrial protocol’ and it is what distinguishes this network. Unlike many options in the industrial Ethernet crowd, EtherNet/IP uses an open protocol at the application layer. Moreover, more than one vendor or organization supports EtherNet/IP. It is the only standard supported by three networking organizations: ControlNet International (CI), the Industrial Ethernet Association (IEA) and the Open DeviceNet Vendor Association (ODVA).

Interface Device: PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix
Manufacturer: Rockwell Automation (Allen Bradley)
Requirements: Rockwell Allen-Bradley – EtherNet/IP (PLC-5, SLC-500, MicroLogix, ControlLogix, CompactLogix and FlexLogix)
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Energy Manager RMS621

The Endress+Hauser Energy Manager RMS621 Driver was designed specifically for the
use with E+H RMS621 energy manager controller. The device, in its various versions,
has a RS232 serial port, 1 RS485 serial port and 1 optional RS485 serial port. The
PC could be connected to one of these serial port. Using the RS485 connection it
is possible to address more than one device, providing that they have different Unit
Number. The RS232 port may exclude the second optional RS485 port; when the cable
is connected to the RS232 port, the second optional RS485 port is disabled. For more
and updated information about these features take as reference the E+H official documentation
of the device that you are going to use.

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Panasonic FP

Panasonic FP allows the data exchange with Panasonic FP series PLCs, using the MEWTOCOL protocol. The driver has been developed for both serial and Ethernet communication.
Before using the driver the PLC must be properly configured through the specific programming software. The Windows version is named “FPWIN GR” or “FPWIN PRO”. The PLC communication parameters may be set by the “OptionPLC Configuration…” menu command in the GR package, while in the PRO package the menu command is under “OnlineCommunication Parameters”.
The Panasonic FP Driver can communicate with either the PLC programming port (“Tool port”) or the PLC “COM port”. For the latter it is important to set the parameter “Port Selection” to the value “Computer Link”.

Note that with this setting the “Communication Format” parameters named “Terminator” and “Header” can be left to their default values (“CR” and “STX not exist”) because they are not used.

The Panasonic FP Driver can also communicate with FP PLCs using TCP/IP over Ethernet.
Panasonic FP Driver supports also the communication via the USB port of the PLC. In this case, the software “Panasonic Electric Works PLC Virtual UART” must be installed.

Please refer to Panasonic documentation for further information.

Interface Device: PLC Panasonic FP Series
Manufacturer: Panasonic
Requirements: Panasonic MEWTOCOL protocol – serial and Ethernet communication
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

SQL Driver

SQL Driver is able to connect to a database server that supports the TCP/IP protocol.
This driver creates a new table in an existing database which allow to record the tag’s name and value. During the runtime the driver create the chosen table in the database and creates one record per tag, once it created all the records it updates only the value of the value column of the specified tag.

Interface Device:
Manufacturer: Progea
Requirements:
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Phoenix Contact PLCI

The Phoenix Contact PLCI driver allows access with symbolic addressing to the data
of these programmable logic controllers:

ILC 1×1, AXC 1xxx, 3xxx AXC and PC WORX RT BASIC / SRT.

The Phoenix Contact PLCI driver communicates with the server devices through the following PLCI libraries (made by PHOENIX CONTACT Software GmbH):

PlciDotNet.dll
PlciDotNet45.dll
PlciBridge.DLL
PLCI.dll
NativeMetaAPI.dll
MetaILP32_10.dll
MetaILP64_10.dll

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

OPC UA Client

OPC Unified Architecture is the new generation from the OPC foundation for data security, reliability and transport.
The OPC UA integrates the current OPC industrial standards with important features such as platform independency, scalability, increased availability and Internet capability.
The OPC UA is no longer based on DCOM and has been designed based on a service-oriented architecture (SOA).

Interface Device: –
Manufacturer: Progea
Requirements: OPC UA Server
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Omron Fins Ethernet

The Omron FINS Ethernet driver was designed specifically for the use with OMRON programmable controllers. This protocol connect a number of OMRON controllers over an Ethernet network.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron FINS Ethernet protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Omron Ethernet-IP

EtherNet/IP is an industrial networking standard that takes advantage of commercial off-the-shelf Ethernet communication chips and physical media. IP stands for ‘industrial protocol’ and it is what distinguishes this network. Unlike many options in the industrial Ethernet crowd, EtherNet/IP uses an open protocol at the application layer. Moreover, more than one vendor or organization backs EtherNet/IP. It is the only standard supported by three networking organizations: ControlNet International (CI), the Industrial Ethernet Association (IEA) and the Open DeviceNet Vendor Association (ODVA).

See the web site https://www.ethernet-ip.org for more information.

This driver has been expressly thought to communicate with Omron NJ and NX PLC series over the Ethernet network. This driver uses symbolic tag addressing (tags names) with Ethernet/IP native commands.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron Ethernet-IP protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

MQTT Client

MQTT Client is a driver over TCP/ IP that implements a “publish-subscribe” lightweight messaging protocol client side. MQTT Client driver requires an MQTT message broker. The broker is responsible for distributing messages to interested clients based on the topic of a message.

Interface Device:
Manufacturer: MQTT
Requirements:
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Modbus RTU

The Modbus Serial Driver was designed for use with serial devices that support the Modbus RTU or Modbus ASCII protocol as “Master”.
Modbus Protocol is a messaging structure developed by Gould Modicon in 1979, used to establish master-slave/client-server communication between intelligent devices. It is a de facto standard, truly open and the most widely used network protocol in the industrial manufacturing environment. It is literally implemented by hundreds of vendors on thousands of different devices in order to transfer discrete/analog I/O and register data between control devices.

Modbus is an application layer messaging protocol, positioned at level 7 of the OSI model, that provides client/server communication between devices connected on different types of buses or networks.
The Modbus protocol has been accepted by the IEC as a Public Available Specification (IEC PAS 62030).
The Modbus Serial driver has been developed to support a wide range of Modbus RTU compatible devices available in the automation world.

The driver permits also to send broadcast messages (only output requests) on device ID 0.

Interface Device: Any standard Modbus Slave device
Manufacturer: Modbus
Requirements: Modbus RTU or Modbus ASCII protocol as Master
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Modbus TCP

Modbus TCP driver has been developed on the basis of Modbus protocol, according to Modbus specification. The driver acts as a client and allows communication with many devices classes supporting this protocol, such as PLCs, remote terminal units, analyzers, I/O modules, sensors, controllers, AC/DC drive control devices. This driver does not implement the Modbus messaging on TCP/IP service. Modbus TCP/IP specification has been developed in 1999. The specification of this protocol and its implementation guide can be obtained on www.modbus.org.
The devices can be direct part of an Ethernet network. The use of interconnection devices like bridge, router or gateway for interconnection between the TCP/IP network and a serial line sub-network permits connections of Modbus serial line client and server end devices. In this latter case, it is important to understand that the communication protocol Modbus TCP/IP is not simply MODBUS over TCP, i.e. is not equal to the MODBUS serial protocol wrapped by a TCP frame. So please be aware that this driver does not support those RS485/Ethernet gateways that add a TCP/IP wrapper to the serial Modbus messages.
The option “String Length” to Exchange Tags in string format has now been added (supported character format: ASCII).

Interface Device: Any standard Modbus Ethernet device
Manufacturer: Modbus
Requirements: Modbus TCP-IP Ethernet protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Modbus Slave

Modbus Slave driver has been developed on the basis of Modbus protocol, according to Modbus specification. MODBUS Protocol is a messaging structure developed by Gould Modicon in 1979, used to establish master-slave/client-server communication between intelligent devices.It is literally implemented by hundreds of vendors on thousands of different devices in order to transfer discrete/analog I/O and register data between control devices. MODBUS is an application layer messaging protocol, positioned at level 7 of the OSI model, that provides client/server communication between devices connected on different types of buses or networks.
The MODBUS protocol has been accepted by the IEC as a Public Available Specification (IEC PAS 62030). The MODBUS Slave driver has been developed to support a wide range of MODBUS compatible devices available in the automation world. The driver simulates one or more MODBUS slaves, defined as stations. The data of the slaves can be defined as tasks, associating the tags of the supervisor to the MODBUS addresses of a slave (station).

Interface Device: Any standard Modbus Master device
Manufacturer: Modbus
Requirements: Modbus RTU or Modbus ASCII protocol as Slave
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Mitsubishi Melsec QE

The “Mitsubishi MELSEC-Q TCP” Driver was designed for use with Mitsubishi MELSEC-Q PLCs equipped with a QJ71E71 communication module, over Ethernet networks.

Interface Device: Mitsubishi Q PLCs or any compatible device.
Manufacturer: Mitsubishi
Requirements: Standard Ethernet cables
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Mitsubishi Melsec FX TCP

The Melsec FX TCP Driver was designed specifically for communication with Mitsubishi FX3U PLCs, connected to the PC through the Ethernet module FX3u-ENET. A number of PLCs can be connected over the Ethernet network. The FX3u-ENET module needs to be configured with a dedicated Mitsubishi software tool.

Interface Device: PLC MELSEC-FX3U
Manufacturer: Mitsubishi
Requirements: Mitsubishi – MELSEC-FX3U Ethernet TCP
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Mitsubishi Melsec FX

The Mitsubishi MELSEC-FX Driver was designed for use with Mitsubishi MELSEC-FX, FX1N, FX2N, FX3U PLCs or any compatible device. The communication protocol used by the driver is the serial point-to-point protocol configurated on the controller’s standard RS-422 port.

Interface Device: PLC Mitsubishi MELSEC-FX, FX1N, FX2N, FX3U
Manufacturer: Mitsubishi
Requirements: Serial Cable
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

LACBUS PC

The Lacbus-PC driver permits communication with lacroix-sofrel devices using the FR1000 front end, that operates as a Gateway, incapsulating messages in Lacbus-PC communication protocol packets from and for devices.
The Lacroix -sofrel devices use 4 different types of communication protocols (Lacbus-RTU, Sofbus-PL, Lacbus-SMS, Sofbus-SMS). The Lacbus-PC driver supports only two of these protocols:

Lacbus-RTU
Sofbus-PL

Interface Device: Driver supports all Lacroix-Sofrel devices that implement the Lacbus RTU and Softbus PL communication protocols by means of connecting with FR 1000.
Manufacturer: Lacroix-Sofrel
Requirements: FR1000 front end
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Konnex -EIB

The EIBus – Konnex Driver was designed specifically to get in communication with Building Automation Devices, connected through EIB bus, or with the new Konnex System, which is the compatible successor of EIB.
EIB devices, like lights, dimmer, lamps, curtains, switches, …, have to be configured for their net address with the aid of the ETS software. In order to operate correctly with EIB devices, a good knowledge of the Konnex architecture and of the ETS software is required. For more information about this bus and the related tools, please refer to www.knx.org
Our driver can operate in Ethernet communication, where the link between IP network and EIB devices are one or more EIBNet/IP routers. Each communication channel requires a dedicated interface.

Interface Device: Any Konnex/EIB devices
Manufacturer: Konnex
Requirements: KONNEX- EIB – Falcon Library (Ethernet)
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

IoT Progea Databoom

The incoming data collected by the service are processed and inserted in a non-relational database which is automatically replicated in several servers to ensure that recorded information is always available. All data are saved automatically by a backup program.

Interface Device: –
Manufacturer: Progea
Requirements: Internet connection
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

IEC 61850 MMS

IEC 61850 is a standard for the design of electrical substation automation, and is a part of the IEC Technical Committe (57 TC57) reference architecture for electric power systems. Data objects and control functionality of a substation are modelled into different standard logical nodes, which can be grouped under different logical devices.

Interface Device: IEC 61850 MMS servers
Manufacturer: –
Requirements:

The driver does not support:

Generic Substation Events (GSEE/GOOSE)
Logs
Sampled Values

Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

IEC 60870-5-104

The IEC Technical Committee 57 ( Working Group 03) have developed a protocol standard for telecontrol, teleprotection, and associated telecommunications for electric power systems. The result of this work is IEC 60870-5. Five documents specify the base IEC 60870-5.

The documents are:

IEC 60870-5-1 Transmission Frame Formats
IEC 60870-5-2 Data Link Transmission Services
IEC 60870-5-3 General Structure of Application Data
IEC 60870-5-4 Definition and coding of Information Elements
IEC 60870-5-5 Basic Application Functions

The IEC Technical Committee 57 have also generated a companion standard IEC 60870-5-104 especially for remote controlled units RTU, connected to a Controlling Station either via TCP/IP networking. The IEC 60870-5-104 is based on the five documents IEC 60870-5-1 – 5 and IEC60870-5-101.

Interface Device: Any RTU compliant, connected to a Controlling Station via TCP/IP networking.
Manufacturer: IEC
Requirements: IEC 60870-5-104 for remote controlled units RTU via TCP/IP
Import Tags: Import Tags not supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Hilscher CifX Multiprotocol

The drivers allow you to access the data card based on the Hilscher netX chip, using the API functions provided by the software “cifX Device Driver”. These are advanced functions that render the protocol used by the Hilscher transparent to the driver in order to communicate with the BUS devices. By configuring the Hilscher card in this way will enable the driver to be used for communicating with both master and slave devices using the following protocols:

AS-Interface
CAN open
CC-Link
CompoNet
DeviceNet
EtherCAT
POWERLINK
PROFIBUS-DP
PROFINET IO RT

Interface Device: All devices that support one of the communication protocols listed above.
Manufacturer: Hilscher
Requirements: An Hilscher NETcoreX board properly configurated.
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

GE srtp2

The GE SRTP2 driver has been developed to exchange data, through Ethernet lan, with GE PLCs series 90. The driver acts as a client. The SRTP2 protocol (Service Request Transfer Protocol 2), often referred to simply as SRTP, is an optimized version of the obsolete protocol SRTP.

Interface Device: GE PLCs series 90.
Manufacturer: Emerson
Requirements: Standard Ethernet cables
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Fatek Ethernet driver

The Fatek Ethernet driver was designed specifically for the use with Fatek Plc seriers
programmable controllers. This protocol connects a number of Fatek controllers over
an Ethernet network:

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Fanuc CNC Ethernet

The Fanuc CNC driver allows access to Fanuc CNC device via Ethernet interface.

List of external packages needed to be installed on the system:

FANUC CNC Focas 1 / Ethernet Library (part number A02B-0207-K732) or FANUC Focas
2 Library (part number A02B-0207-K737)
Microsoft .NET Framework 4.7 Developer Pack

To execute this driver, Movicon (and the I/O Data Server) must be executed at 32-bit. To enable Movicon to be executed at 32-bit also in Windows 64-bit installations,
execute these commands from the shell (with administrator privileges):

“C:\Program Files (x86)\Microsoft SDKs\Windows\v10.0A\bin\NETFX 4.7 Tools\CorFlags.exe”
“c:\Program Files\Progea\Movicon.NExT 4.0\MoviconNExT.exe” /32BITREQ+

“C:\Program Files (x86)\Microsoft SDKs\Windows\v10.0A\bin\NETFX 4.7 Tools\CorFlags.exe”
“c:\Program Files\Progea\Movicon.NExT 4.0\PlatformNextIOServer.exe” /32BITREQ+

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

B&R

The “B&R PVI” Driver was designed specifically for use with B&R devices that implement the communication protocol INA2000.The connection can be a point-to-point serial connection (RS-232 or RS-422) or a multi-point Ethernet connection. This driver requires the installation of B&R PVI libraries.

Interface Device: devices that implement the communication protocol INA2000
Manufacturer: B&R
Requirements: B&R PVI libraries.
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Twincat

This driver needs the ADS software library (from Beckhoff) in order to communicate with the routing system that rules every intermodule exchange of data. PLCs and I/O systems are controlled by the TwinCAT System Control Module, make sure that this Configuration end monitoring system is correctly set up and enabled, before establishing communication.
For the use of TwinCAT System Control and PLC, please refer to Beckhoff TwinCAT documentation.

Interface Device: Beckhoff TwinCat SoftPLC Beckhoff I/O
Manufacturer: Beckhoff
Requirements: Require ADS Software Library
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

BacNet/IP

The BACnet/IP driver provides communication with devices supporting BACnet protocol in its implementation over IP.
BACnet is a protocol defined by ASHRAE (American Society of Heating, Refrigeration and Air-conditioning Engineers). The ANSI/ASHRAE Standard 135-2004 document contains the protocol definition. Annex to the document contains specification of the BACnet transported over IP, which is the implementation chosen for this driver.

The BACnet protocol has a number of services that permit to read/write the properties of the configured Data Objects. In order to get the value of the property “Present_Value”, it is possible to choose between two ways : sending a request “ReadProperty” or subscribing a COV (Change Of Value) notification for the Data Object. Using the service “ReadProperty” means polling the object with a request, and receive an answer containing the data; using COV notification means subscribing to the device for a notification when the “Present_Value” of a Data Object changes. This second way results in a spontaneous message from the device, whenever a Present_Value changes its value, reducing the traffic at the minimum.

Interface Device: Any standard device BacNet/IP
Manufacturer: BacNet
Requirements: Binary / Analog / Multistate – I/O and value
Import Tags: Support Import Tags
Operating System: WIN 32/64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

3S CODESYS

The CODESYS Driver was designed specifically to get in communication with 3S Software softPLC, connected through TCP/IP network protocols. An instance of the CODESYS SoftPLC can be installed on a desktop computer or on a Windows CE panel; the driver is able to access both. Our driver support PLC versions 3. The runtime and the Programming environment are different for the two versions, for the configuration of the 3S system, please refer to their documentation.

- Interface Device: 3S Software CODESYS SoftPLC version 3
- Manufacturer: 3S
- Requirements: In order to communicate with the device it is necessary to install the “CODESYS Gateway” application on the PC where NExT will be executed.
- Import Tags: Import Tags supported
- Operating System: WIN 64

This section cannot be accessed by “Guest” users and requires the “User” level reserved for customers who own development license. If you own a development license and have not yet been enabled at User level, please send a request email to [email protected], specifying the Serial Number of your development license and the Username to be enabled.

Download links:

Movicon.NExT – Ver. 4.0.300

Omron Host Link

The Omron Host Link Driver was designed for use with Omron PLCs. The protocol Host Link is a serial multi-point protocol of type Master/Slave. The driver plays the role of master.

Interface Device: Omron SYSMAC PLCs
Manufacturer: Omron
Requirements: Omron Host Link serial protocol
Import Tags: Support Import Tags
Operating System: WIN 32/64, Win CE

Download links:

Movicon 11 – Rel. 11.4.1.8 DBL286

Movicon 11 CE – Rel. 11.4.1.8 DBL286

Hitachi Ethernet

The Hitachi Ethernet H-protocol driver supports the communication with PLCs Hitachi of EH and EHV series, equipped with a built-in Ethernet port or an Ethernet communication module.
This driver implements the task codes A0h, Read I/O (continuous address), and A2h, Write I/O (continuous address), of the Ethernet H-protocol.

Interface Device: –
Manufacturer: Hitachi
Requirements: Hitachi Ethernet, EHV, EH series
Import Tags: Import Tags Not Supported
Operating System: WIN 32/64

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Hilscher NET Link

The Hilscher NetLink driver provides Simatic MPI communication to Siemens devices via the Hilscher ‘NetLink’ Ethernet interface. This driver was designed specifically for the use with Siemens S7 300 and 400 and VIPA System 200V, 300V, 300S and 500S series.

Before the Netlink device can be used, an appropriate system configuration must be set. In particular you have to specify a valid IP address for the Netlink device. For further details please refer to “Netlink configuration” .
A single Hilscher NetLink driver can manage communication with a single Netlink device. This does not prevent from communicating with more PLCs at a time.
As an example, you can connect 3 PLCs with different MPI IDs through a standard Profibus cable, then connect the Netlink device to the MPI port of one of the PLCs and you will access all the 3 PLCs data areas.
The driver should be configured with 3 stations, each one with the specific MPI station ID of the related PLC, but all the stations must have the same IP address (server address), that is the IP address of the Netlink device as specified in “Netlink configuration” .

The use of more Netlink devices at a time is possible by duplicating the driver, that is creating a copy on the driver for each Netlink device in use. For further details see “Driver duplication” in the Supervisor manual.

Interface Device: Simatic S7-300, S7-400, VIPA PLC
Manufacturer: Hilscher
Requirements: HilscherNetLink RJ45 Ethernet cable and SyCon. Simatic MPI protocol via Hilscher NetLink Ethernet interface (Simatic S7-300, S7-400,VIPA)
License Code: License Code Not required
Import Tags: Support Import Tags
Operating System: WIN 32/64, WIN CE

Download links:

Movicon 11 – Rel. 11.4.1.5 DBL286

Movicon 11 CE – Rel. 11.4.1.5 DBL286

Company Name	Address	Phone Number	E-mail Address	Web Site	Sectors
Anblick Consultant Pvt. Ltd.	F/B – 64 Lajpat Nagar, Sahibabad, Ghaziabad, U.P, 201005 India	+91-120-4238324	[email protected]		Automation Process control Building automation
Armax Automation Private Limited	NO 51& 54, 2nd Cross, Vinayaka Layout, Andhrahalli Main Road, Peenya 2nd Stage, Bangalore-91 India	+91-80-32467600	[email protected]	www.armaxindia.com	Automation Process control Building automation
Equvera Applied Automation #5, VL Puram Main Road, Ambattur, Chennai, Tamil Nadu, India	#5, VL Puram Main Road, Ambattur, Chennai, Tamil Nadu, India	Mob : +91 97898 15345 / +91 98848 35702	[email protected]	www.equvera.com	Automation

News:

Progea is now part of Emerson.

I/O Drivers

I/O Drivers List for Movicon 11

Listed below are the I/O Drivers that are available and included within the software product

Unternehmen

Produkte

Lösungen

Fallstudien

Support

Movicon NE.xT-Ressourcen

Movicon 11.6-Ressourcen

Partner

News

My Progea

Partita IVA 01997840366 – R.E.A. MO-257822

© All right Reserved 2020

Partita IVA 01997840366 – R.E.A. MO-257822 © All right Reserved 2020

Partita IVA 01997840366 – R.E.A. MO-257822
© All right Reserved 2020